guides

Record Speeds and Sizes: 33, 45 and 78 RPM, 7 vs 12 Inch

By Droc Published

Most records are one of three kinds: a 12-inch LP at 33 1/3 rpm, a 7-inch single at 45 rpm, or an old 10-inch shellac disc at 78 rpm. Size is the quickest clue, but not a guarantee. The speed printed on the label decides it, and the exceptions (12-inch singles at 45, 7-inch discs at 33 1/3, 10-inch LPs) are common enough to check every time.

Quick answer: the three speeds and sizes

FormatTypical sizeSpeedTypical materialUsual playing time per side
LP (album)12 inch (30 cm)33 1/3 rpmVinylUp to about 22 minutes at the maximum, 15 to 18 for best quality
Single7 inch (18 cm)45 rpmVinylAbout 3.5 minutes for best quality, 4.5 maximum
7810 inch (25 cm), sometimes 12 inch (30 cm)78 rpm (78.26 as standardised in 1925)ShellacAbout 3 minutes (10 inch) or 4 to 5 minutes (12 inch)

The playing-time figures for vinyl come from the disc manufacturer Disc Makers, which publishes minutes per side “for optimal quality” and a “max length” for each size and speed (read as of November 2026). The 78 figures come from Yale University Library’s history of the 78 rpm record, which gives about three minutes for a 10-inch side and four to five minutes for a 12-inch side.

If a record does not match this table, use the identification checklist below.

What speed is my record?

The label is the authority: labels usually print the speed, such as “33 1/3 RPM” or “45 RPM”. When neither the label nor the sleeve gives a speed, size and material narrow it down:

  1. Measure or compare the diameter. 7 inch, 10 inch or 12 inch.
  2. Read the label. A printed speed settles the question.
  3. Look at the centre hole. A large hole of about 1.5 inches marks a 7-inch single made for RCA-style 45 rpm changers (see centre holes and adapters below).
  4. Check the material and weight. Shellac made 78s heavy and fragile, according to the Spark Museum, and Classic45s calls shellac “brittle and noisy”, so a rigid, heavy 10-inch disc is most likely a 78. Lighter, flexible vinyl usually means a microgroove record at 33 1/3 or 45, although some 78s were pressed in vinyl (see the 78 section).
  5. Look at the grooves. 78s are coarse-groove records, while LPs and 45s are microgroove. The stylus sizes show the difference: about 2.5 to 3 mil (thousandths of an inch) tip radius for a 78 against 0.7 to 1.0 mil for LPs and 45s, according to the stylus supplier Esoteric Sound.
  6. Check the run time. A 12-inch side that runs longer than about 12 minutes is very likely 33 1/3, because 12 minutes is Disc Makers’ maximum for a 12-inch side at 45. A 12-inch record with only one or two long tracks a side may be a 12-inch single, which can be cut at either speed.
  7. Use your ears if nothing is printed. At the wrong speed, voices sound slowed and low, or sped up and high.

Size alone can mislead: 12-inch singles, 10-inch LPs, 7-inch 33 1/3 discs and 12-inch 78s all exist, so the printed label outranks any rule of thumb.

78 rpm shellac discs

For about fifty years from around 1900, the 10-inch 78 was the record industry’s standard format, according to the Spark Museum. Yale University Library adds that 78s were still mass-produced alongside the newer formats into the 1950s but had faded from the scene by 1955. Yale notes that early disc speeds varied widely, that by 1910 most records ran at about 78 to 80 rpm, and that in 1925 a speed of 78.26 rpm was chosen as the standard for motorised phonographs. The number is an arithmetic by-product: a 3,600 rpm motor driving through a 46-tooth gear gives 3,600 / 46 = 78.26. The Physics Factbook, a student-written compilation edited by Glenn Elert, quotes Roland Gelatt’s 1955 history The Fabulous Phonograph for the same arithmetic with a synchronous motor, and for speeds that “hovered between 74 and 82 revolutions per minute” from 1900 to 1925. A New Scientist answer quoted on the same page says standardisation “did not begin until 1912”, so sources differ on when the industry first settled near 78.

Two facts matter when playing 78s today:

  • They were not all recorded at exactly 78. In a 1977 interview with James A. Drake, first published by Mainspring Press in 2024, the former Columbia research director William Bachman, citing Aida Favia-Artsay’s study of Caruso’s Victor records, said recording speeds could vary by as much as five rpm from one session to the next. Yale adds that Columbia issued 80 rpm discs for some time after 1920. The right playback speed for an early 78 is therefore not always 78.
  • The material is shellac. Yale’s history says shellac became the most common material, which is why 78s are also called shellac records. The label ”78s” itself, Yale adds, only came into use after the Second World War, when a name was needed to tell these discs from newer formats. During and after the war, when shellac was scarce, some 78s were pressed in vinyl, including the six-minute 12-inch V-Discs made for US troops.

Playing time was the format’s limit: about three minutes a side on a 10-inch disc and four to five minutes on a 12-inch. Broadcasting magazine’s report of the LP launch in 1948 noted that “the average 12-inch double-faced record now in use plays about eight minutes”. Longer works needed several 78s sold together in bound sleeves, the Library of Congress notes, which is how the word “album” came to mean a long-playing record.

Columbia’s 33 1/3 rpm LP (1948)

Columbia unveiled its long-playing Microgroove record in New York in June 1948. Broadcasting’s report of 28 June 1948 says the record was “demonstrated in New York June 18”; the Library of Congress’s 2019 blog post dates the Waldorf-Astoria press conference to 21 June, the date by which Columbia’s demonstration albums were due at its distributors.

Key documented details:

  • The speed was 33 1/3 rpm, the records came in 10-inch and 12-inch sizes, and a side held “up to 22½ minutes” (Broadcasting) or “about 23 minutes” (Library of Congress). The 12-inch LP quickly became the standard format for commercial recordings.
  • Broadcasting gave launch prices of $4.85 for a 12-inch and $3.85 for a 10-inch Masterworks disc, $2.85 for a popular 10-inch, and $29.95 plus tax for a Philco M-15 player that attached to existing radios and radio-phonographs.
  • Columbia’s 1949 catalogue, quoted by the Library of Congress, called the discs “nonbreakable Vinylite” and claimed they held “approximately six times as much music as conventional shellac records”.
  • The Library of Congress credits Peter Goldmark and his team of Columbia and CBS engineers with perfecting the microgroove in the summer of 1947, and shares the credit among Goldmark, who oversaw the project, the engineer and research director Bill Bachman, and several other engineers. In the Mainspring Press interview, Bachman says Goldmark was so involved in television work that he asked Bachman to run LP development day to day.

The technical write-up of the system appeared as Goldmark, Snepvangers and Bachman, “The Columbia Long-Playing Microgroove Recording System”, Proceedings of the IRE, vol. 37, no. 8 (August 1949), pp. 923-927.

Why 33 1/3?

The speed is older than the LP: it came from film sound. Western Electric and Bell Labs’ Vitaphone system of 1926 used 16-inch discs at 33 1/3 rpm on a turntable driven by the projector, for a running time of about 10 minutes, which matched a single 1,000-foot reel of 35 mm film, according to Mix magazine. The Science Museum Group’s record of a 1930 Vitaphone disc calls 33 1/3 “a speed first used for this system”.

By the time of the LP, the speed was an industry standard. Bachman told Drake that “33-1/3 r.p.m. was already the standard for cutting [radio] transcription discs and also for the old Vitaphone discs”, so RCA Victor’s failed long-playing discs of the early 1930s had offered nothing new in speed. In January 1949, Broadcasting reported Columbia’s chairman, Edward Wallerstein, stressing that 33 1/3 rpm “has been standard in the professional recording industry” and was used by broadcasting stations. A month later, Broadcasting reported his argument that RCA’s attempt at a 33 1/3 record had failed and Columbia’s had succeeded because it was coupled with a microgroove and a “feather-light tone-arm”. The Library of Congress reaches the same conclusion: the vinyl and the speed existed by the 1920s, and “it was the microgroove that ultimately proved crucial”.

RCA Victor’s 45 rpm single (1949) and the format war

RCA Victor answered with a smaller disc. Broadcasting reported on 17 January 1949 that RCA had shown its “Madame X” 45 rpm record and changer to the press in New York the previous Monday, 10 January, a day after Columbia introduced a 7-inch 33 1/3 microgroove disc. RCA’s record measured 6⅞ inches and played up to 5 minutes 15 seconds a side, and the changer, loaded with eight records, played 42 minutes. RCA’s president, Frank Folsom, said RCA had taken part in meetings with Columbia before the LP launch and decided not to go along. The records and players reached shops at the end of March: Broadcasting reported on 4 April 1949 that they “went on sale late last week”, and the Spark Museum gives 31 March 1949.

The fight that followed, known as the Battle of the Speeds, ran for about two years. The later rows below come from the timeline at microgroove.jp, a research site on the history of record equalisation:

DateEventSource
18 June 1948Columbia demonstrates the 33 1/3 LP in New York, in 10-inch and 12-inch sizesBroadcasting, 28 June 1948
9 January 1949Columbia introduces a 7-inch 33 1/3 discBroadcasting, 17 January 1949
10 January 1949RCA Victor shows the 45 rpm record and its changerBroadcasting, 17 January 1949
February 1949Capitol sides with RCA’s 45 and Mercury with Columbia; Decca stays neutral, making only 78sBroadcasting, 14 February 1949
Late March 1949RCA’s 45 records and players go on sale (31 March, per the Spark Museum)Broadcasting, 4 April 1949
August 1949Decca chooses the LP; Capitol adopts it too and supports all three speedsmicrogroove.jp
April 1950RCA Victor begins releasing 33 1/3 LPsmicrogroove.jp
August 1950Columbia begins releasing 45 rpm discsmicrogroove.jp
About 1951Columbia’s 7-inch 33 1/3 disc quietly disappearsmicrogroove.jp

The outcome was a division of labour rather than a winner: the 12-inch LP became the album format and the 7-inch 45 became the single, as microgroove.jp’s account puts it. Classic45s notes that RCA sold inexpensive players with a spindle that could hold a stack of 45s, and that by the mid-1950s the 45 was the main format for new songs, fed by Top 40 radio and teenage buyers.

7 inch vs 12 inch: sizes, speeds and playing time

Size and speed set how long a side can run. A faster record passes more inches of groove under the stylus each second, which improves fidelity but shortens playing time, and the more minutes a side holds, the closer and shallower the grooves have to be and the quieter the record plays, Disc Makers explains. Its published limits (as of November 2026) are:

SizeSpeedBest quality (min per side)Maximum (min per side)
12 inch33 1/3 rpm15 to 1822
12 inch45 rpm912
7 inch33 1/3 rpm4.56
7 inch45 rpm3.54.5

Disc Makers advises coming in “a minute or two under” the maximum and recommends 45 rpm for 7-inch records, since at 33 1/3 they are “sometimes prone to distortion”. These are one manufacturer’s published limits for new pressings.

The two sizes suit different jobs. At 15 to 22 minutes per side, a 12-inch 33 1/3 disc fits an album of 30 to 44 minutes across two sides. A 7-inch 45 fits one song per side, which suited RCA’s view, as the Spark Museum puts it, that a record should not need to hold more than one song. A 12-inch at 45 rpm allows only 9 to 12 minutes per side in the same table. The “7-inch” single is slightly smaller than its name: RCA’s original 45 measured 6⅞ inches (about 17.5 cm).

12-inch singles

The 12-inch single came out of disco. Estelle Caswell’s 2019 Vox Earworm video, presented by Bunk History, credits the disco pioneer Tom Moulton with an accidental studio discovery in 1976 and says the format dominated pop by the 1980s. Its reasoning: a 7-inch 45 holds only about 3:30 of quality audio, too short for the long dance tracks DJs played. A 12-inch single can be cut at either speed, since Disc Makers lists 12-inch records at 33 1/3 (up to 22 minutes a side) and at 45 (up to 12), so the label decides.

Centre holes and 45 adapters

The 45’s big centre hole comes from RCA’s changer. Broadcasting’s report of the January 1949 launch describes a 1½-inch spindle that housed the changer’s “trigger-fast” drop mechanism and held up to eight records, with raised areas on each disc’s non-playing surfaces so that the playing surfaces of stacked records did not touch. A 45 made for that system has a centre hole of about 1.5 inches (38 mm). LPs have a small hole that fits a turntable’s spindle directly.

To play a large-hole 45 on an ordinary turntable, use a 45 adapter (also sold as an EP adaptor), which centres the record on the thin spindle. Some turntables include one: the accessory list for the Technics SL-1200M7B, for example, includes an “EP record adaptor” (Panasonic specification page). A 7-inch record with a small hole fits the spindle directly and needs no adapter.

The RIAA curve, and why 78s need different styli and EQ

Records are cut with the bass reduced and the treble boosted, and the phono preamp applies the inverse curve on playback so that the combined response is flat; the point of the recording curve is to save groove space, as Texas Instruments explains in the phono-preamp example of its OPA1641 datasheet. The standard curve, named after the Recording Industry Association of America (RIAA), is set by three time constants, 3180, 318 and 75 microseconds, which put its turning points near 50 Hz, 500 Hz and 2,122 Hz. TI also notes an IEC amendment that adds a further pole at about 20 Hz to keep excessive low-frequency content away from loudspeakers.

The history matters for old records:

  • Hackaday dates RIAA’s place as the de facto standard to 1954. It is the curve an ordinary record preamplifier assumes, and before it “basically every publisher had their own standard”.
  • microgroove.jp’s history of the standard reports that the 1953 NARTB broadcast standard, the AES playback curve of 1954 and the RIAA’s 1954 characteristic were effectively the same curve, identical to RCA Victor’s “New Orthophonic”, and quotes RCA engineer R. C. Moyer’s 1957 count of “at least eight different recognized characteristics” in use or under consideration in the early 1950s.
  • The same site notes that late-1950s mono amplifiers offered extra EQ positions (Columbia LP, NAB, AES and 78 rpm) for records pressed before 1954, while 70 of the 76 phono-equipped stereo amplifiers in Audio magazine’s August 1964 product preview had only an RIAA position.

So a modern phono preamp, or a turntable with a built-in preamp, is set for the RIAA curve and suits LPs and 45s from 1954 on. A 78 or an early microgroove record may need a different curve. In the video Hackaday describes, its maker, Techmoan, sidesteps the RIAA stage for 78s by taking the signal straight from the cartridge.

Styli for 78s

A 78 needs a much larger stylus than a microgroove record. Hackaday explains that a standard microgroove stylus is “comically undersized” for a 78: it drags along the bottom of the groove and misses the sound pattern cut higher up the groove walls. The answer is a dedicated mono 78 stylus, which Hackaday noted in 2023 can be bought from Audio-Technica and other brands. Esoteric Sound gives tip radii of about 0.7 to 1.0 mil for LP and 45 styli and about 2.5 mil for 78 styli, lists Shure’s 78 styli at 2.5 mil, Stanton’s at 2.7 mil, Grado’s at 3.0 mil and Audio-Technica’s ATN3600-78 at 2.9 mil, and warns that “3 mil stylus” is often a rounded label for any 78 stylus. Its practical advice is 3.0 mil for most pre-1940 78s, because a larger tip rides higher in a well-played groove and avoids some of the wear, and 2.5 or 2.7 mil for later ones. Tracking force varies by stylus, so the range its maker specifies is the one to use.

Which speeds does a turntable play?

A turntable’s specifications list the speeds it plays. Technics’ SL-1200M7B, for example, plays 33 1/3 and 45 rpm and reaches 78 rpm by a switch, with wow and flutter of 0.025% W.R.M.S., according to Panasonic’s specification page (as of November 2026). Playing 78s well takes three things from the sections above: a 78 rpm setting, a 78 stylus of about 2.5 to 3 mil, and a playback curve other than RIAA where the record needs one.

How to identify your record: checklist

CheckIf this is trueLikely speed
Label prints a speedIt says 33 1/3, 45 or 78Use it
12 inch, vinyl, long sideRoughly 15 to 22 minutes per side33 1/3
7 inch, vinyl, one song per sideUp to about 4.5 minutes per side45
7 inch, large 1.5-inch holeMade for RCA-style changers45, needs an adapter
10 inch, rigid, heavy, coarse groovesShellac, typically made before the mid-1950s78
12 inch, one or two long tracks per sideDance or club single45 or 33 1/3; check the label

If you are building a collection, how to start a vinyl collection covers choosing first records and grading condition, the vinyl setup cost guide prices a complete turntable-and-speaker setup including the phono stage, and vinyl vs streaming compares the formats.

Sources